MC Three-terminal Positive Voltage Regulator These voltage regulators are monolithic integrated circuits designed as fixedvoltage regulators for a wide. MC Fairchild datasheet pdf data sheet FREE Datasheets (data sheet) search for integrated circuits (ic), semiconductors and other electronic components. Motorola Semiconductor MC datasheet, (MC Series) Three Terminal Positive Fixed Voltage Regulators (1-page), MC datasheet, MC pdf.
|Published (Last):||16 June 2016|
|PDF File Size:||10.90 Mb|
|ePub File Size:||13.43 Mb|
|Price:||Free* [*Free Regsitration Required]|
Values of less than 0. XX, These two digits of the type number indicate nominal voltage. Sign up using Facebook. Long Term Stability – Output voltage stability under accelerated life test conditions with the maximum rated voltage listed in the devices’ electrical characteristics and maximum power dissipation.
Since the output is 12 volts, you add the two together to get a minimum input of Voltage regulators basically can be divided in two big groups: From what i understand then from your answer The maximum dropout voltage Vd is 2. NCV prefix is for automotive and other applications requiring site and mc78112 control.
All parameters are specified under certain conditions, and for the output voltage we can see datasheeet the condition is that the input voltage is minimum In many low current applications, compensation capacitors are not required. How does it go from a Maximum dropout voltage to a minimum input voltage?
I’ve seen Datasheeg with a dropout voltage of 50 mV. Output Noise Voltage – The rms ac voltage at the output, with constant load and no input ripple, measured over a specified frequency range. Machine Model Method V. The datasheet does say how much it needs, but you may have to look for it.
The current sensing PNP must be able datashewt handle the short circuit current of the three-terminal regulator. The minimum voltage obtainable with this arrangement is 2.
Datasheets search archive of electronic components datasheets
From the above it may look like you best make your input voltage a lot higher than the 12V output, but that’s not true. Even though the typical dropout voltage is 2 volts, you should use the maximum value in your design. Current Boost Regulator Figure Linear regulators are different.
The input voltage must remain typically 2. An input bypass capacitor should be selected to provide good high-frequency characteristics to insure stable operation under all load conditions.
But since there’s this voltage drop the input voltage has to be higher than the output voltage. Therefore it’s best to keep the input voltage just above the minimum to prevent the regulator to become overheated.
With adequate heatsinking they can deliver output currents in excess of 1. Email Required, but never shown. A note on dissipation: So if you have a 12W load it will draw 1A from the regulator. Pulse testing with low duty cycle is used. Peter Mortensen 1, 3 14 For example, a 1.
mc, buy mc, specification & datasheets
This is a snapshot of page 8: Short Circuit Protection http: On page 6 of the datasheet, the maximum dropout voltage Vd is listed as 2. These regulators employ internal current limiting, thermal shutdown, and safe-area compensation. So the 20V delivers 20W, while the load only consumes 12W. Maximum Ratings are stress ratings only.
In order to minimize dissipation the MCC is chosen in this application. There are LDOs Low Drop-Out which still can regulate the output if the input is only a few hundreds of mV higher and there datashfet even ultra low drop-out types which only need a few tens of mV. The circuit of Figure 10 can be modified to provide supply protection against short circuits by adding a short circuit sense resistor, RSC, and an additional PNP transistor. If so, what is the current like that mc781 outputs? Dean 4, 22 57 Resistor R in conjunction with the VBE of the PNP determines when the pass transistor begins conducting; this circuit is not short circuit proof.
Changes in VO due to heating effects must be taken into account separately.
On the datasheet it doesn’t mention an input voltage. Resistor R determines the current as follows: Load and line regulation are specified at constant junction temperature. If we look further we can see two values for line regulation; it appears that this is best if the input voltage is at least 16V.
Internal Short Circuit Current Limiting? The bypass capacitor should be mounted with the shortest possible leads directly across the regulators input terminals. The MJ provides current to 5.
Internal Thermal Overload Protection? All linear regulators have a minimum dropout voltageor difference.
The is not a LDO low-dropout regulatoras the typical dropout voltage is around 2 volts.