Model APSC. Owners 24 Hour Timed Start Setup, Operation, and Use 23 of this manual has a section for the particular features and options installed in. Save this Book to Read prestige apsc installation manual PDF eBook at our Online Library. Get prestige apsc installation manual PDF. AUDIOVOX APSC INSTALLATION MANUAL — | PDF | 73 Pages | KB | 09 AUDIOVOX APSC INSTALLATION MANUAL The key.
|Published (Last):||3 February 2010|
|PDF File Size:||6.2 Mb|
|ePub File Size:||1.39 Mb|
|Price:||Free* [*Free Regsitration Required]|
This wire will show 0 volts when the key is turned to the “OFF” Don’t show me this message again. Special considerations must be made for windshield glass as some newer vehicles utilize a metallic shielded window glass that will inhibit or restrict RF reception. Shock Sensor By Pass: Mechanical Neutral Start Switch from starting in gear.
PLATINUM APSC INSTALLATION MANUAL Pdf Download.
You can enter Bank 3 from Bank 2 by turning the ignition key off then on after you’ve made inatallation changes you wanted in Bank 2, Siren two Long ChirpYou can also go right to bank 3 by: By pressing ‘print’ button you will print only current page. Audiovox car security system installation manual 24 pages. Got it, continue to print.
The following procedure must be performed after the installation of any Remote Start Device. Once activated, the unit will start 1 time if the vehicle temperature reaches “0 ” and then will run the allotted time. If this wire is not used or you have difficulty accessing the glow plug preheat circuit, you may elect to utilize the Diesel timed output as specified in Remote Start feature selection 9.
Do not remove the fuse holders from this wire harness. To achieve optimum performance the coil signals must be evenly distributed.
Prestige APS-997C Installation Manual
Ignition xps997c Output Connect this wire to the ignition 2 wire from the ignition switch. Page 24 To connect to the key in sensor circuit as shown for method 2: Connect this wire to the vehicle’s parking light feed wire. The unit will monitor the voltage level of the battery during remote start, wait for the voltage to drop while cranking, then look for the voltage instalpation to go above the level it was before the vehicle began to crank which indicates the vehicle is running.
Add to my manuals Add.
Multi Coil Adaptor Optional Information. The Superheterodyne Receiver Antenna Assembly provided with this unit allows routing from below the dash board for maximum operating range. If the vehicle has delay interior lights, and you wish to avoid three chirp, defect zone, indication normally associated with this type of interior light, we suggest you learn the interior light delay.
Page 25 To decrease sensitivity, turn the adjustment screw counter clockwise. Monitoring The Vehicle’s Engine: Page 27 b 27 of This unit has the ability to learn the dome light delay time, up to 60 seconds. If the vehicle’s parking lights are ground switched, connect this wire to chassis ground. Page 18 Connector Port The 4 pin port located on the side of this module is for proprietary Audiovox data bus interface modules. After you have confirmed the operation of the Audiovox Remote Start unit and tested all the safety features of the system: Choose a location above the belt line dashboard of the vehicle for best reception.
Page 3 3 of Locate the control wire that connects the drivers door pin switch to the key in sensor switch. By pressing ‘print’ button you will print only current page.
Add to my manuals Add. Parking Light Flasher Output This wire is the normally open contact of the on board parking light flash relay.
Page 16 These applications require the use of additional components which may include relays, fixed resistors, or for convenience, a Door Lock Interface. Page 11 ground trigger output wire of motion detectors, microwave detectors, or glass break detectors, can be connected to this Light Green trigger input wire. To print the manual completely, please, installaton it.
This is accomplished by first mapping out the firing order of the engine in groups of as indicated below. In this application, the Red wire of the door lock harness provides a ground pulse during the arming sequence, or pulsed ground lock output.
This wire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect to the negative side of the ignition coil.